Made with Formlio



Chinook Works

Aerolume at NAMX Toronto

Brief and constraints



What the stand has to do



Aerolume's first public showing of the AL-4 since its Series B. The stand has one job: get qualified operators into a 25-minute demo slot, and log every one of them.



Island site H-214, 12 by 10 m, 6 m height limit, hall floor rated to 10 kN/m². The full-scale AL-4 cabin mock-up weighs 1,840 kg, which sets the floor, the rigging and the build order.

The main risk is freight. The mock-up leaves Aerolume's Mirabel hangar on 4 October. If it slips past 11 October, we build around a scaled model instead.

The stand in four numbers



Every figure below is checked against the NAMX exhibitor manual, revision 3, and the hall's floor loading certificate.




0 m²



Island site H-214


0 m



Maximum build height


0 kg



Cabin mock-up weight


0



Demo slots, three days

Four zones, one route through



Visitors enter at the open corner, see the aircraft first, and leave through the meeting lounge. Footfall modelled at 410 visitors an hour at peak.



The cabin, full scale

The AL-4 cabin on a 300 mm steel plinth, doors open, four seats live. Load spread over a 4 by 3 m steel plate so the hall floor stays under 6 kN/m².


Full-scale aircraft cabin on a plinth

The flight wall

An 8 by 3.5 m LED wall, 2.6 mm pitch, running the Mirabel test-flight footage on a 90-second loop. Rigged from our own ground-supported frame, no hall rigging points needed.


LED wall showing aerial footage

Demo pods

Three acoustic pods, 2.4 m square, each with a VR flight demo and a tablet that books the next slot. Every booking lands in Aerolume's CRM with consent captured.


Three acoustic demo pods

Operator lounge

A 28 m² raised lounge for twelve, with a coffee point and a private room for two. This is where the commercial team closes, so it is screened from the aisle.


Meeting lounge on an exhibition stand
Every visitor who sits in the cabin leaves a booked demo behind.
Every visitor who sits in the cabin leaves a booked demo behind.
Every visitor who sits in the cabin leaves a booked demo behind.
Every visitor who sits in the cabin leaves a booked demo behind.
Every visitor who sits in the cabin leaves a booked demo behind.

Design and build method



Fourteen weeks from signature to doors. Every stage ends in a written sign-off, so a late change has a known cost.



Concept and 3D model

Three weeks. A real-time model of the stand in the hall, with sightlines from every aisle. Two rounds of changes.

Engineering and approvals

Stamped structural drawings, rigging-free LED frame calculations and the organiser's stand plan approval, due 3 September.

Fabrication in Calgary

Five weeks in our Foothills workshop. Modular aluminium frame, FSC plywood skins, every panel numbered for reuse.

Freight and build

Two trucks east, five build days on site, cabin craned in on day two before the floor is laid around it.

Show, derig, report

Two crew on stand all three days. Derig in one night, and a lead and footfall report within ten working days.

Stands we have built for hardware companies



Chinook Works is eleven people. Priya Natarajan leads design and Owen Brisebois runs build; both are named on this job.



They put a 2.1 tonne drilling rig on a hall floor rated for less and had the load-spread calculations stamped before we asked. The show manager signed it off in a day.

Tamsin Whitehorse

Head of Events, Albedo Robotics

Our stand came back from Houston with one damaged panel out of 214. We have now used the same frame at four shows in two countries.

Marc-André Lussier

Marketing Director, Glacis Hydrogen

The demo booking flow on the stand fed our CRM directly. We had 61 qualified meetings in the pipeline before the show closed.

Hana Okabe-Reid

VP Commercial, Stratus Thermal

Three build options



All figures in CAD, plus 13% HST. Fixed for the scope above. Project management is 8% of the line items; contingency is 5% and is only invoiced against a logged change. We recommend the owned modular stand: it pays back by the second show.





Hired structure

One show. We hire the frame and print single-use skins.

Subtotal
$126588.00
Total (before tax)
$126588.00
HST (13%)
$16456.44
Total
$143044.44

Hired structure

One show. We hire the frame and print single-use skins.

Item
Price
Quantity
Total

Design and engineering





$19100.00

Hired frame and printed skins





$31480.00

Cabin plinth and load plate





$8460.00

LED wall, pods and AV





$34640.00

Freight, build and derig





$17950.00

Project management, 8%





$8930.00

Contingency, 5%





$6028.00
Subtotal
$126588.00
Total (before tax)
$126588.00
HST (13%)
$16456.44
Total
$143044.44

Owned modular stand

Recommended. Aerolume owns a reusable stand, built for 120 m² and reducible to 60.

Subtotal
$164453.00
Total (before tax)
$164453.00
HST (13%)
$21378.89
Total
$185831.89

Owned modular stand

Recommended. Aerolume owns a reusable stand, built for 120 m² and reducible to 60.

Item
Price
Quantity
Total

Design and 3D model





$18640.00

Engineering and approvals





$6380.00

Modular frame and skins

Aluminium frame, FSC plywood, 214 numbered panels.



$52970.00

Cabin plinth and load plate





$8460.00

LED wall, pods and AV





$34640.00

Freight, build and derig





$23930.00

Project management, 8%





$11602.00

Contingency, 5%





$7831.00
Subtotal
$164453.00
Total (before tax)
$164453.00
HST (13%)
$21378.89
Total
$185831.89

Owned stand, three shows

The recommended stand, stored between shows and rebuilt twice more in 2028.

Subtotal
$216344.00
Total (before tax)
$216344.00
HST (13%)
$28124.72
Total
$244468.72

Owned stand, three shows

The recommended stand, stored between shows and rebuilt twice more in 2028.

Item
Price
Quantity
Total

Owned modular stand

The six build lines from the middle option.



$145020.00

Storage and refurbishment

Climate-controlled, Calgary, inspected after each show.



$7840.00

Two further show builds

Freight, crew, LED hire and derig per show.



$37920.00

Project management, 8%





$15262.00

Contingency, 5%





$10302.00
Subtotal
$216344.00
Total (before tax)
$216344.00
HST (13%)
$28124.72
Total
$244468.72

Fourteen weeks to doors



Counted back from Tuesday 19 October. Thanksgiving Monday is a non-working day for our crew and the hall. Assumes signature by Friday 9 July.



DayWeekMonthQuarterSemesterYear
M7Jul
M8Aug
M9Sep
M10Oct
M11Nov
M12Dec
Concept and 3D model, two rounds
Structural engineering and LED frame calcs
Organiser stand plan approval
Fabrication, Foothills workshop
Cabin mock-up leaves Mirabel
Freight Calgary to Toronto
On-site build, five days
NAMX open, three days
Overnight derig
Lead and footfall report
Design12 - Jul 31

Concept and 3D model, two rounds



Engineering2 - Aug 28

Structural engineering and LED frame calcs



EngineeringAug 30 - Sep 4

Organiser stand plan approval

Organiser review, up to five working days.

BuildAug 30 - Oct 2

Fabrication, Foothills workshop



Build4 - Oct 9

Cabin mock-up leaves Mirabel

Aerolume's freight. Plan B if it slips past 11 October.

Build4 - Oct 9

Freight Calgary to Toronto



Show12 - Oct 19

On-site build, five days



Show19 - Oct 22

NAMX open, three days



Show21 - Oct 22

Overnight derig



ReportOct 25 - Nov 6

Lead and footfall report



Assumptions, risks and terms



Stated now, with the number attached, so nothing on this list becomes a surprise in October.



Excluded from the fee

Space rental, the organiser's mandatory services (power, compressed air, internet, cleaning), hall rigging, catering, staff travel and the cabin mock-up's own freight. Our estimate for organiser services is 23,400 plus HST. We order them for you and pass them through at cost.

If the cabin mock-up is late

The plinth is designed to take a 1:4 scale model as well. If the cabin is not on a truck by 11 October, we switch to the model and credit 4,180 from the plinth and rigging lines.

Payment schedule

50% on signature, 30% on 30 August when fabrication starts, 20% within 14 days of the report. The deposit is non-refundable once materials are ordered.

Cancellation

Before 30 August, design and engineering at cost. From 30 August, 60% of the fee. Inside 21 days of build, 100%, because freight and crew are committed.

Changes after sign-off

Each stage closes with a written sign-off. Changes after that are priced in writing before we act on them, drawn from the 5% contingency first.

Ownership and reuse

Aerolume owns the stand and the 3D files on final payment. Storage in Calgary is 640 a month if you do not take the three-show option.

What happens next



This proposal holds until Friday 2 July 2027. After that our August workshop slot goes to another build, and fabrication would start two weeks later than shown.



Prepared by



Priya Natarajan Design Director, Chinook Works

Unit 4, 6120 11 Street SE Calgary AB T2H 2L7 priya@chinookworks.ca

For approval by



Danielle Okafor-Lavoie Head of Marketing, Aerolume

We can walk your team through the 3D model on a call any weekday before 2 July.

Approved
Slide to approve
En approuvant ce document, vous le signez électroniquement.

Approve the stand

By confirming, you approve the option selected above, plus 13% HST, for delivery between 12 July and 6 November 2027, and authorise the 50% deposit invoice. We then book Foothills workshop time and lodge the stand plan with NAMX.